Engineering Mechanics ›› 2018, Vol. 35 ›› Issue (7): 47-54.doi: 10.6052/j.issn.1000-4750.2017.03.0213

Previous Articles     Next Articles

BUCKLING OF PURLINS SUPPORTING STANDING SEAM ROOF WITH ONE SAG-ROD

TANG Ya-jun, TONG Gen-shu, ZHANG Lei   

  1. College of Civil Engineering & Architecture, Zhejiang University, Hangzhou 310058, China
  • Received:2017-03-17 Revised:2017-09-08 Online:2018-07-25 Published:2018-07-26

Abstract: Buckling of purlins, supporting standing seam roof, simply supported at both ends and acted by pure moment, is studied by a closed-form solution. The uniform distributed torsional restraint provided by the roof sheeting and the lateral elastic restraint provided by the sag-rod placed at the mid-span are considered. The analytical solutions are found, the threshold stiffness of the sag-rod, at which the buckling mode changes from symmetrical buckling to anti-symmetrical one is observed and developed, and the discussion extended to the effects of many factors such as the cross-sectional profile, span length, torsional restraint, sag-rod's stiffness and the height of the sag-rod connecting point along the web on the buckling moment and threshold stiffness. A simplified formula for the buckling moment is also presented based on the calculations covering almost full ranges of various parameters. The investigation shows that the purlin buckles into only one half-wave no matter how large the uniform distributed torsional restraint is, which differs fundamentally from the buckling of a compressed column on a Winkle foundation where several half waves are possible if the elastic stiffness is large enough.

Key words: stability, thin-walled member, purlin, sag-rod, torsional restraint, threshold stiffness

CLC Number: 

  • TU391
[1] 陈明, 黄骥辉, 赵根田. 组合截面冷弯薄壁型钢结构研究进展[J]. 工程力学, 2016, 33(12):1-11 Chen Ming, Huang Jihui, Zhao Gentian. Research process of compound section cold-formed thin-wall steel structures[J]. Engineering Mechanics, 2016, 33(12):1-11. (in Chinese)
[2] 白凡, 杨娜, 王晓峰. 简支C型檩条在风吸力作用下精确应力计算模型[J]. 工程力学, 2017, 34(3):131-140. Bai Fan, Yang Na, Wang Xiaofeng. Analytical method for simply supported c-sections purlins under wind uplift loadings[J]. Engineering Mechanics, 2017, 34(3):131-140. (in Chinese)
[3] 姚谏. 普通卷边槽钢的弹性畸变屈曲荷载[J]. 工程力学, 2008, 25(12):30-34. Yao Jian. Distortional buckling loads of cold-formed lipped channels[J]. Engineering Mechanics, 2008, 25(12):30-34. (in Chinese)
[4] 童根树, 冯一笑, 张磊. 受弯Z形檩条畸变屈曲与整体屈曲统一分析方法[J]. 工程力学, 2017, 34(5):116-124, 131. Tong Genshu, Feng Yixiao, Zhang Lei. A unified analysis method for distortional and global buckling of Z-purlins in flexure[J]. Engineering Mechanics, 2017, 34(5):116-124, 131. (in Chinese)
[5] 童根树, 樊勇伟, 张磊. C形和Z形檩条的弹性弯扭屈曲分析[J]. 钢结构, 2015, 30(10):9-17. Tong Genshu, Fan Yongwei, Zhanglei. Elastic flexural-torsional buckling of C-purlin and Z-purlin[J]. Steel Construction, 2015, 30(10):9-17. (in Chinese)
[6] Zhang L, Tong G S. Lateral buckling of simply supported C-and Z-section purlins with top flange horizontally restrained[J]. Thin-Walled Structures. 2016, 99:155-167.
[7] 刘逸祥, 童根树, 张磊. 风吸力作用下仅考虑扭转约束的Z形和C形檩条弹性弯扭屈曲[J]. 四川大学学报(工程科学版), 2015, 47(1):118-127. Liu Yixiang, Tong Genshu, Zhang Lei. Elastic stability of cold-formed Z & C purlins under wind suction considering the effects of torsional restraint[J]. Journal of Sichuan University (Engineering Science Edition), 2015, 47(1):118-127. (in Chinese)
[8] 刘逸祥, 童根树, 杜慧琳, 等. 立缝支架屋面体系对Z型檩条扭转约束的试验研究和有限元分析[J]. 建筑结构学报, 2014, 35(11):116-124. Liu Yixiang, Tong Genshu, Du Huilin, et al. Test and finite element analysis on torsional restraint of corrugated steel sheet to purlin through clips[J]. Journal of Building Structures, 2014, 35(11):116-124. (in Chinese)
[9] 童根树, 邵峰. 压型钢板屋面对檩条的扭转约束[J]. 工业建筑, 2010, 40(3):111-115. Tong Genshu, Shao Feng. Torsional restraint on purlins by corrugated steel sheet[J]. Industrial Construction, 2010, 40(3):111-115. (in Chinese)
[10] 童根树. 拉条在檩条侧向稳定中的作用[J]. 工业建筑, 2013, 43(12):52-56. Tong Genshu. Efficiency of sag rods as lateral supports for stability of purlins[J]. Industrial Construction, 2013, 43(12):52-56. (in Chinese)
[11] Zhang L, Tong G S. Lateral buckling of C-section purlins with one anti-sag bar at middle span section[J]. Thin-Walled Structures, 2016, 102:246-257.
[12] Zhang L, Tong G S. Stress analysis on cold-formed C-purlins subjected to wind suction load considering the effective stiffness of anti-sag bar[J]. Thin-Walled Structures, 2015, 90:107-118.
[13] 童根树. 钢结构的平面外稳定[M]. 北京:中国建筑工业出版社, 2013. Tong Genshu. Out-of-plane stability of steel structures[M]. Beijing:China Architecture Industry Press, 2013. (in Chinese)
[14] Polyzois D. Sag rods as lateral supports for girts and purlins[J]. Journal of Structural Engineering, 1987, 113(7):1521-1531.
[15] Hancock G J, Trahair N S. Lateral buckling of roof purlins with diaphragm restraints[J]. Computer Programs, 1978, 20:10-15.
[16] Larue B, Khelil A, Gueury M. Elastic flexural-torsional buckling of steel beams with rigid and continuous lateral restraints[J]. Journal of Constructional Steel Research, 2007, 63(5):692-708.
[17] Mohammadi E, Hosseini S S, Rohanimanesh M S. Elastic lateral-torsional buckling strength and torsional bracing stiffness requirement for monosymmetric I-beams[J]. Thin-Walled Structures, 2016, 104(3):116-125.
[18] Nguyen C T, Joo H S, Moon J, et al. Flexural-torsional buckling strength of I-girders with discrete torsional braces under various loading conditions[J]. Engineering Structures, 2012, 36(5):337-350.
[19] Tong G S, Chen C S. Buckling of laterally and torsionally braced beams[J]. Journal of Constructional Steel Research, 1988, 11(1):41-55.
[20] 刘占科, 周绪红. 薄壁构件弯扭屈曲总势能的完备性分析[J]. 工程力学, 2017, 34(7):1-10. Liu Zhanke, Zhou Xuhong. An analysis on completeness of total potential energy of thin-walled members with flexural-torsional buckling[J]. Engineering Mechanics, 2017, 34(7):1-10. (in Chinese)
[21] 童根树. 钢结构的平面内稳定[M]. 北京:中国建筑工业出版社, 2005. Tong Genshu. In-plane stability of steel structure[M]. Beijing:China Architecture Industry Press, 2015. (in Chinese)
[22] Sun K, Tong G, Zhang L. Twisting about constrained line of parallel purlins inter braced by sagrods under wind suctions[J]. Thin-Walled Structures, 2016, 108:30-40.
[23] Ziemian R D, Ziemian C W. Formulation and validation of minimum brace stiffness for systems mw of compression members[J]. Journal of Constructional Steel Research, 2017, 129:263-275.
[1] YUE Zi-xiang, WEN Qing-jie, ZHUO Tao. Stability analysis of half-through truss bridge [J]. Engineering Mechanics, 2018, 35(S1): 270-277.
[2] YING Hong-wei, WANG Xiao-gang, ZHANG Jin-hong. ANALYSIS ON HEAVE-RESISTANT STABILITY CONSIDERING THE EFFECT OF EXCAVATION WIDTH [J]. Engineering Mechanics, 2018, 35(5): 118-124.
[3] LIU Xing-wang, TONG Gen-shu, LI Ying, HU Huan, CHEN Dong. STABILITY ANALYSIS OF ASSEMBLY STEEL STRUTS IN DEEP EXCAVATION [J]. Engineering Mechanics, 2018, 35(4): 200-207,218.
[4] PU Li-dong, LUO Wu-kui, YAN Ze-zhou. OPTIMAL DESIGN FOR NOTCH FILTER OF AEROSERVOELASTIC SYSTEMS [J]. Engineering Mechanics, 2018, 35(4): 235-241.
[5] TANG Zhen-yun, GUO Jun, HONG Yue, LI Yi, LI Zhen-bao. AN ANALYTICAL METHOD OF SYSTEM STABILITY FOR MDOF REAL-TIME SUBSTRUCTURING TESTING [J]. Engineering Mechanics, 2018, 35(3): 22-29.
[6] LI Peng-fei, ZHU Qi-zhi, GU Shui-tao, NI Tao. A PHASE FIELD METHOD TO SIMULATE CRACK NUCLEATION AND CRACK PROPAGATION IN ROCK-LIKE MATERIALS [J]. Engineering Mechanics, 2018, 35(3): 41-48.
[7] ZHANG Ai-lin, GUO Zhi-peng, LIU Xue-chun, LI Chao. GLOBAL STABILITY COEFFICIENT OF PREFABRICATED BEAMS WITH DUAL-CHANNEL COMBINED SECTION [J]. Engineering Mechanics, 2018, 35(2): 67-75.
[8] LIU Xin-xin, TANG Chun-an, GONG Bin, YU Qing-lei. RESEARCH ON THE STABILITY OF THE WEST SLOPE OF THE HEISHAN IRON MINE BASED ON THE DDD CENTRIFUGAL LOADING METHOD [J]. Engineering Mechanics, 2018, 35(1): 191-200.
[9] WANG Duo-zhi, LI Wen-liang, ZHI Xu-dong. STATIC STABILITY ANALYSIS OF RETICULATED SHELL WITH PURLIN ROOFING SYSTEM [J]. Engineering Mechanics, 2017, 34(增刊): 71-77,98.
[10] WANG Yu-hang, WU Qiang, XIONG Guang-liang. TEST STUDY ON MECHANICAL PROPERTIES OF SHEAR PANEL ENERGY-DISSIPATION COMPONENTS USING LOW YIELD POINT STEEL WITH DIFFERENT PARAMETERS [J]. Engineering Mechanics, 2017, 34(7): 21-22.
[11] LI Yang, ZHOU Li, YANG Bing-cai. FLUTTER BOUNDARY PREDICTION OF TURBULENCE EXCITATION RESPONSE BASED ON RANDOM DECREMENT METHOD [J]. Engineering Mechanics, 2017, 34(6): 9-16.
[12] TONG Gen-shu, FENG Yi-xiao, ZHANG Lei. A UNIFIED ANALYSIS METHOD FOR DISTORTIONAL AND GLOBAL BUCKLING OF Z-PURLINS IN FLEXURE [J]. Engineering Mechanics, 2017, 34(5): 116-124,131.
[13] LIU Zhan-ke, ZHOU Xu-hong. GENERAL SUMMATION FORMULAE OF MONOSYMMETRY SECTION CONSTANTS OF THIN-WALLED MEMBERS [J]. Engineering Mechanics, 2017, 34(5): 23-29.
[14] XU Xin-yu, LI Yong-le, LIAO Hai-li, REN Sen. FLUTTER OPTIMIZATION OF A DOUBLE-DECK TRUSS-STIFFENED GIRDER THREE-TOWER SUSPENSION BRIDGE BY WIND TUNNEL TESTS [J]. Engineering Mechanics, 2017, 34(5): 142-147.
[15] BAI Fan, YANG Na, WANG Xiao-feng. ANALYTICAL METHOD FOR SIMPLY SUPPORTED C-SECTIONS PURLINS UNDER WIND UPLIFT LOADINGS [J]. Engineering Mechanics, 2017, 34(3): 131-140.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] CHENG Yong-feng, ZHU Zhao-qing, LU Zhi-cheng, ZHANG Fu-you. THE DYNAMIC RESPONSE OF A SIMPLY SUPPORTED VISCOUSLY DAMPED BEAM SYSTEM UNDER A MOVING HARMONIC OSCILLATOR[J]. Engineering Mechanics, 2018, 35(7): 18 -23 .
[2] WANG Pi-guang, ZHAO Mi, DU Xiu-li. EARTHQUAKE INDUCED HYDRODYNAMIC PRESSURE ON ELLIPTICAL CYLINDER SURROUNDED BY COMPRESSIBLE WATER[J]. Engineering Mechanics, 2018, 35(7): 55 -61 .
[3] HONG Yue, TANG Zhen-yun, LIN Shu-chao, LI Zhen-bao. Experimental study on mechanical properties of a new type of VCFPB[J]. Engineering Mechanics, 2018, 35(S1): 113 -119 .
[4] SHANG Qing-xue, LI Ze, LIU Rui-kang, WANG Tao. Experimental study on properties of aseismic braces used in pipe line systems[J]. Engineering Mechanics, 2018, 35(S1): 120 -125,133 .
[5] JI Xiao-dong, CHENG Xiao-wei, XU Meng-chao. Experimental study on tension-shear behavior of low-aspect-ratio RC walls[J]. Engineering Mechanics, 2018, 35(S1): 53 -61 .
[6] ZHENG Wen-bin, ZHANG Jian-wei, CAO Wan-lin. Shaking table test study on L-shaped shear walls with single layer of web reinforcement[J]. Engineering Mechanics, 2018, 35(S1): 134 -139 .
[7] BA Zhen-ning, PENG Lin, LIANG Jian-wen, HUANG Di-yang. SCATTER AND DIFFRACTION OF ARBITRARY NUMBER OF HILLS FOR INCIDENT PLANE P-WAVES[J]. Engineering Mechanics, 2018, 35(7): 7 -17,23 .
[8] YAN Wang-ji, WANG Peng-peng, SUN Qian, REN Wei-xin. RECENT ADVANCES IN SYSTEM IDENTIFICATION USING THE TRANSMISSIBILITY FUNCTION[J]. Engineering Mechanics, 2018, 35(5): 1 -9,26 .
[9] SUN Shan-shan, ZHAO Jun-hai, HE Shuan-hai, CUI Ying, LIU Yan. DYNAMIC RESPONSE OF CONCRETE-FILLED STEEL TUBE PIERS UNDER BLAST LOADINGS[J]. Engineering Mechanics, 2018, 35(5): 27 -35,74 .
[10] LIU Ming-ming, LI Hong-nan, FU Xing. EXPERIMENTAL AND NUMERICAL ANALYSIS OF AN INNOVATIVE RE-CENTERING SHAPE MEMORY ALLOYS-SHEARING LEAD DAMPER[J]. Engineering Mechanics, 2018, 35(6): 52 -57,67 .