Engineering Mechanics ›› 2017, Vol. 34 ›› Issue (4): 22-31.doi: 10.6052/j.issn.1000-4750.2016.11.0871

Previous Articles     Next Articles

INFLUENCE OF SEISMIC ACTION ADJUSTMENTS ON SEISMIC DESIGN AND SAFETY OF RC FRAMES

LU Xiao1, LU Xin-zheng2, LI Meng-ke3, GU Dong-lian2, XIE Lin-lin4   

  1. 1. School of Civil Engineering, Beijing Jiaotong University, Beijing 100044, China;
    2. Department of Civil Engineering, Tsinghua University, Beijing 100084, China;
    3. China Architecture Design Group, Beijing 100044, China;
    4. School of Civil and Transportation Engineering, Beijing University of Civil Engineering and Architecture, Beijing 100044, China
  • Received:2016-11-08 Revised:2016-12-28 Online:2017-04-25 Published:2017-04-25

Abstract: The experience of Wenchuan earthquake and Lushan earthquake shows that the actual seismic intensity suffered by buildings was often much greater than the code-specified seismic design intensity, which caused very serious damage to buildings. Although the seismic safety margin of buildings in China is in continuous improvement with the updating of seismic design code and seismic hazard map, many experts still believe that to date the seismic safety level of buildings in China is not sufficient yet. Hence, how to determine the reasonable seismic action is important and meaningful to ensure the seismic safety. Based on a series of reinforced concrete frames designed according to the Code for Seismic Design of Buildings (GB 50011-2010), these frames are redesigned with the adjustments of seismic design parameters, including dynamic amplification factor (bmax), seismic action, and dead and live load combination factors. The earthquake-induced collapse analysis is conducted for these frames. Consequently, the influence of the adjustments on the seismic forces, material consumption and seismic safety is discussed. The results indicate that the parameters adjustments make the axial compression ratio for columns increase by about 8%, and the reinforcement ratio for beams and slabs increase by about 6%. For frames whose collapse starts from the bottom story, the parameters adjustments can obviously improve the seismic safety of the frames. However, with the increasing of seismic design intensity, the increased amplitude of seismic safety will decrease slightly.

Key words: seismic action, RC frame, axial compression ratio, earthquake-induced collapse analysis, seismic safety

CLC Number: 

  • TU375.4
[1] 王亚勇, 戴国莹. 《建筑抗震设计规范》的发展沿革和最新修订[J]. 建筑结构学报, 2010, 31(6): 7―16. Wang Yayong, Dai Guoying. Evolution and present updation of `Code for seismic design of buildings' [J]. Journal of Building Structures, 2010, 31(6): 7―16. (in Chinese)
[2] 清华大学土木工程结构专家组, 西南交通大学土木工程结构专家组, 北京交通大学土木工程结构专家组, 等. 汶川地震建筑震害分析[J]. 建筑结构学报, 2008, 29(4): 1―9. Civil and Structural Groups of Tsinghua University, Xinan Jiaotong University and Beijing Jiaotong University. Analysis on seismic damage of buildings in the Wenchuan earthquake [J]. Journal of Building Structures, 2008, 29(4): 1―9. (in Chinese)
[3] 陆新征, 林旭川, 田源, 等. 汶川, 芦山, 鲁甸地震极震区地面运动破坏力对比及其思考[J]. 工程力学, 2014, 31(10): 1―7. Lu Xinzheng, Lin Xuchuan, Tian Yuan, et al. Comparison and discussion on destructive power of the ground motions recorded in the hardest-hit regions of Wenchuan, Lushan and Ludian earthquakes [J]. Engineering Mechanics, 2014, 31(10): 1―7. (in Chinese)
[4] 陈肇元. 跋——汶川地震教训与震后建筑物重建、加固策略[R]. 汶川地震——建筑震害调查与灾后重建分析报告. 北京: 中国建筑工业出版社, 2008. Cheng Zhaoyuan. Postscruip: lessons from Wenchuan earthquake and strategies for post-earthquake reconstruction and retrofit [R]. WenChuan Earthquake: Report of Building Seismic Damage Survey and Post-earthquake Reconstruction Analysis. Beijing: China Architecture and Building Press, 2008. (in Chinese)
[5] 施炜, 叶列平, 陆新征, 等. 不同抗震设防 RC 框架结构抗倒塌能力研究[J]. 工程力学, 2011, 28(3): 41―48. Shi Wei, Ye Lieping, Lu Xinzheng, et al. Study on the collapse-resistant capacity of RC frames with different seismic fortification levels [J]. Engineering Mechanics, 2011, 28(3): 41―48. (in Chinese)
[6] 陈肇元, 徐有邻, 钱稼茹. 土建结构工程的安全性与耐久性[J]. 建筑技术, 2002, 33(4): 248―253. Chen Zhaoyuan Xu Youlin Qian Jiaru. Safety and durability of structural works in civil engineering [J]. Architecture Technology, 2002, 33(4): 248―253. (in Chinese)
[7] 蒲德群, 刘西拉. 我国建筑结构安全水平的合理设置[J]. 岩石力学与工程学报, 2007, 26(增刊1): 2292―2299. Pu Dequn, Liu Xila. Reasonable settlement of structural safety level in China [J]. Chinese Journal of Rock Mechanics and Engineering, 2007, 26(Suppl 1): 2292―2299. (in Chinese)
[8] GB 18306-2015, 中国地震动参数区划图[S]. 北京: 中国标准出版社, 2015. GB 18306-2015, Seismic ground motion parameters zonation map of China [S]. Beijing: Standards Press of China, 2015. (in Chinese)
[9] GB 50011-2010, 建筑抗震设计规范[S]. 北京: 中国建筑工业出版社, 2010. GB 50011-2010, Code for seismic design of buildings [S]. Beijing: China Architecture & Building Press, 2010. (in Chinese)
[10] 施炜. RC框架结构基于一致倒塌风险的抗震设计方法研究[D]. 北京: 清华大学, 2014. Shi Wei. Uniform collapse risk targeted seismic design methodology for reinforced concrete frame structures [D]. Beijing: Tsinghua University, 2014. (in Chinese)
[11] 陆新征, 叶列平. 基于IDA分析的结构抗地震倒塌能力研究[J]. 工程抗震与加固改造, 2010, 32(1): 13―18. Lu Xinzheng, Ye Lieping. Study on the seismic collapse resistance of structural system [J]. Earthquake Resistant Engineering and Retrofitting, 2010, 32(1): 13―18. (in Chinese)
[12] Lu X, Lu X Z, Guan H, et al. Collapse simulation of reinforced concrete high-rise building induced by extreme earthquakes [J]. Earthquake Engineering & Structural Dynamics, 2013, 42(5): 705―723.
[13] 曲哲, 叶列平. 摇摆墙-框架体系的抗震损伤机制控制研究[J]. 地震工程与工程振动, 2011, 31(4): 40―50. Qu Zhe, Ye Lieping. Seismic damage mechanism control of rocking wall frame system [J]. Journal of Earthquake Engineering and Engineering Vibration, 2011, 31(4): 40―50. (in Chinese)
[14] GB 50010-2010, 混凝土结构设计规范[S]. 北京: 中国建筑工业出版社, 2010. GB 50010-2010, Code for design of concrete structures [S]. Beijing: China Architecture & Building Press, 2010. (in Chinese)
[15] Bousalem B, Chikh N. Development of a confined model for rectangular ordinary reinforced concrete columns [J]. Materials and Structures, 2007, 40(6): 605―613.
[16] 汪训流, 陆新征, 叶列平. 往复荷载下钢筋混凝土柱受力性能的数值模拟[J]. 工程力学, 2007, 24(12): 76―81. Wang Xunliu, Lu Xinzheng, Ye Lieping. Numerical simulation for the hysteresis behavior of RC columns under cyclic loads [J]. Engineering Mechanics, 2007, 24(12): 76―81. (in Chinese)
[17] 叶列平. 混凝土结构(上册)[M]. 北京: 中国建筑工业出版社, 2012: 14―44. Ye Lieping. Concrete structures (Volume 1) [M]. Beijing: China Architecture & Building Press, 2012: 14―44. (in Chinese)
[18] FEMA P695. Quantification of building seismic performance factors [R]. Washington, D.C.: Federal Emergency Management Agency, 2009.
[19] 陆新征, 马玉虎, 陈浩宇, 等. 7度区典型框架教学楼抗震加强措施效果对比[J]. 地震工程与工程振动, 2011, 31(1): 124―129. Lu Xinzheng, Ma Yuhu, Chen Haoyu, et al. Comparison among different strengthening methods for a typical RC classroom frame in zones with seismic intensity VII [J]. Journal of Earthquake Engineering and Engineering Vibration, 2011, 31(1): 124―129. (in Chinese)
[20] 唐代远, 陆新征, 叶列平, 等. 柱轴压比对我国RC框架结构抗地震倒塌能力的影响[J]. 工程抗震与加固改造, 2010, 32(5): 26―35. Tang Daiyuan, Lu Xinzheng, Ye Lieping, et al. Influence of axial compression ratio to the seismic collapse resistance of RC frame structures [J]. Earthquake Resistant Engineering and Retrofitting, 2010, 32(5): 26―35. (in Chinese)
[1] JIA Hong-yu, DU Xiu-li, LI Lan-ping, HUANG Sheng-qian, ZHENG Shi-xiong. PROBABILITY ANALYSIS OF POUNDING SEPARATION DISTANCE OF BRIDGES SUBJECTED TO EARTHQUAKE EXCITATIONS [J]. Engineering Mechanics, 2018, 35(8): 39-45.
[2] GAO Jia-ming, LIU Bo-quan, HUANG Hua, ZHOU Chang-quan. THEORETICAL ANALYSIS ON THE PROGRESSIVE COLLAPSE OF RC FRAME STRUCTURES WITH SLABS [J]. Engineering Mechanics, 2018, 35(7): 117-126.
[3] ZHEN Wei, SHENG Ping, YANG Qing-shan, TIAN Chun-yu. STUDY ON VERTICAL SEISMIC ACTION AND SHAKING TABLE TEST OF GUARDIAN ART CENTER [J]. Engineering Mechanics, 2018, 35(6): 200-208,230.
[4] SUN Xiao-yun, HAN Jian-ping, DANG Yu, ZHOU Ying. EFFECT OF GROUND MOTION DURATION ON SEISMIC FRAGILITY OF RC FRAMES WITH DIFFERENT BEAM-COLUMN JOINT FAILURE MODES [J]. Engineering Mechanics, 2018, 35(5): 193-203.
[5] ZHENG Shan-suo, LIU Wei, ZUO He-shan, DONG Li-guo, LI Qiang-qiang. ASEISMIC PERFORMANCE TEST OF RC FRAME BEAMS CONSIDERING CORROSION WITH DIFFERENT SHEAR SPAN RATIO IN THE COASTAL ATMOSPHERE [J]. Engineering Mechanics, 2018, 35(4): 78-86.
[6] YAN Xin-tong, XU Long-he. MULTI-OBJECTIVE OPTIMIZATION OF GENETIC ALGORITHM-BASED FAILURE MODE FOR REINFORCED CONCRETE FRAME-SHEAR WALL STRUCTURES [J]. Engineering Mechanics, 2018, 35(4): 69-77.
[7] ZHOU Zhou, YU Xiao-hui, LU Da-gang. FRAGILITY ANALYSIS AND SAFETY EVALUATION OF REINFORCED CONCRETE FRAME STRUCTURES SUBJECTED TO MAINSHOCK-AFTERSHOCK EARTHQUAKE SEQUENCES [J]. Engineering Mechanics, 2018, 35(11): 134-145.
[8] ZHENG Shan-suo, LIU Wei, QIN Qing, ZHANG Chuan-chao, DONG Li-guo, LI Qiang-qiang. EXPERIMENTAL RESEARCH ON SEISMIC BEHAVIOR OF RC FRAME BEAMS UNDER DIFFERENT LOADING PROTOCOLS [J]. Engineering Mechanics, 2018, 35(1): 109-117.
[9] LÜ Da-gang, DAI Kuang-yu, YU Xiao-hui, LI Ning. SEISMIC FRAGILITY ANALYSIS ON NON-DUCTILE RC FRAME STRUCTURES RETROFITTED WITH FRP [J]. Engineering Mechanics, 2017, 34(增刊): 49-53,70.
[10] LI Yan-jun, LÜ Da-gang, WANG Zhen-yu. THE OVERSTRENGTH FACTOR OF RC FRAMES WITH INFILLED WALLS BASED ON ADAPTIVE POA AND IDA [J]. Engineering Mechanics, 2017, 34(增刊): 197-201.
[11] ZHANG Pei-zhou, SUN Bao-yin, GU Quan, OU Jin-ping. REFINED ASEISMIC ANALYSIS OF LOW-DUCTILITY RC FRAME BUILDING BASED ON NUMERICAL SUBSTRUCTURE METHOD [J]. Engineering Mechanics, 2017, 34(增刊): 38-48.
[12] HAN Jian-ping, LIU Wen-lin. EXPERIMENTAL INVESTIGATION ON SEISMIC BEHAVIOR OF PVA FIBER REINFORCED CONCRETE COLUMNS WITH HIGH AXIAL COMPRESSION RATIOS [J]. Engineering Mechanics, 2017, 34(9): 193-201.
[13] ZHENG Shan-suo, ZUO He-shan, LIU Wei, HUANG Ying-ge, ZHOU Jing-liang, ZHENG Jie. EXPERIMENTAL RESEARCH ON ASEISMIC BEHAVIORS OF RC FRAME BEAMS OF LOW SHEAR SPAN RATION IN GENERAL ATMOSPHERIC ENVIRONMENT [J]. Engineering Mechanics, 2017, 34(7): 186-194.
[14] LU Jie-zhi, ZHANG Yao-ting, GUO Zong-ming, WANG Xiao-wei. SEISMIC FRAGILITY ANALYSIS OF MULTI-STOREY PC FRAME STRUCTURES USING INCREMENTAL DYNAMIC ANALYSIS [J]. Engineering Mechanics, 2017, 34(6): 109-119.
[15] WANG Xian-tie, LIU Li-da, YANG Hang-dong, LIN Lin-hui. SEISMIC STUDY OF CONCRETE-FILLED SQUARE STEEL TUBULAR FRAME-THIN STEEL PLATE SHEAR WALLS WITH TWO-SIDE OPENINGS [J]. Engineering Mechanics, 2017, 34(3): 162-172.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] YUAN Yuan;;XU Ying-qiang;LU Guo-zhi;ZHU Xian-fei. NUMERICAL METHOD FOR RESIDUAL STRESS OF GEAR IN SHAKEDOWN[J]. Engineering Mechanics, 2008, 25(10): 0 -211, .
[2] XING De-jin;LI Zhong-xian. FUZZY CONTROL OF STRUCTURES USING SMA SMART DAMPER[J]. Engineering Mechanics, 2008, 25(10): 0 -228, .
[3] ZHOU Xiao-ping;YANG Hai-qing;ZHANG Yong-xing. ELASTOPLASTIC ANALYSIS OF A FINITE PLATE WITH AN ECCENTRIC CRACK LOADED BY TWO PAIRS OF CONCENTRATED TENSILE FORCES[J]. Engineering Mechanics, 2008, 25(1): 0 -027 .
[4] GONG Yao-qing;BAO Shi-hua. A NEW METHOD FOR FREE VIBRATION ANALYSIS OF SPACE MEGA FRAME OF SUPER TALL BUILDINGS[J]. Engineering Mechanics, 2008, 25(10): 0 -140 .
[5] LIU Jin-xing;DENG Shou-chun;ZHANG Jing;LIANG Nai-gang. BEAM LATTICE MODELING FOR THE FRACTURE OF PARTICLE COMPOSITES[J]. Engineering Mechanics, 2008, 25(10): 0 -037 .
[6] LANG Feng-chao;XING Yong-ming;ZHU Jing. THE MECHANICAL PROPERTIES OF 316L STAINLESS STEEL AFTER SURFACE NANOSTRUCTURE TREATMENT USING NANOINDENTATION[J]. Engineering Mechanics, 2008, 25(10): 0 -071 .
[7] GUO Xiao-gang;;LIU Ren-huai;ZENG Na;JIN Xing. THE MODIFICATION ON SPACE CONFIGURATION OF FLEXIBLE PIPE BY THE SUB-STRUCTURE DISPLACEMENT ITERATION METHOD[J]. Engineering Mechanics, 2008, 25(10): 0 -032 .
[8] XING Jing-zhong;LIU Chun-tu. BUCKLING ANALYSIS OF SPANNING PIPE BURIED IN LINEAR ELASTIC SOIL[J]. Engineering Mechanics, 2008, 25(10): 0 -075 .
[9] LIU Xiang-qing;LIU Jing-bo. TIME HISTORY ANALYSIS OF ELASTO-PLASTIC SEISMIC RESPONSE OF A SUBWAY STATION STRUCTURE WITH ARCHED CROSS SECTION BASED ON FIBER MODEL[J]. Engineering Mechanics, 2008, 25(10): 0 -157 .
[10] HAO Qing-duo;WANG Yan-lei;HOU Ji-lin;OU Jin-ping;. EXPERIMENTAL STUDY ON BOND BEHAVIOR OF GFRP RIBBED REBARS[J]. Engineering Mechanics, 2008, 25(10): 0 -165, .