工程力学 ›› 2018, Vol. 35 ›› Issue (12): 143-150.doi: 10.6052/j.issn.1000-4750.2017.09.0741

• 土木工程学科 • 上一篇    下一篇

不锈钢焊接箱形截面压弯构件弯曲屈曲试验研究

杨璐1, 宁克洋1, 班慧勇2, 赵梦晗1   

  1. 1. 北京工业大学建筑工程学院, 北京 100124;
    2. 清华大学土木工程系, 清华大学土木工程安全与耐久教育部重点实验室, 北京 100084
  • 收稿日期:2017-09-28 修回日期:2018-01-04 出版日期:2018-12-14 发布日期:2018-12-14
  • 通讯作者: 杨璐(1982-),男,湖北人,教授,博士,博导,主要从事钢结构和组合结构方面的研究(E-mail:lyang@bjut.edu.cn). E-mail:lyang@bjut.edu.cn
  • 作者简介:宁克洋(1992-),男,安徽人,硕士生,主要从事钢结构方面的研究(E-mail:1748262874@qq.com);班慧勇(1985-),男,内蒙古人,研究员,博士,主要从事结构工程研究(E-mail:banhy@tsinghua.edu.cn);赵梦晗(1992-),女,北京人,硕士生,主要从事钢结构方面的研究(E-mail:18801190691@126.com).
  • 基金资助:
    国家自然科学基金面上资助项目(51478019);北京市科技新星计划项目(2016117)

EXPERIMENTAL RESEARCH ON FLEXURAL BUCKLING OF STAINLESS STEEL WELDED BOX-SECTION BEAM-COLUMNS

YANG Lu1, NING Ke-yang1, BAN Hui-yong2, ZHAO Meng-han1   

  1. 1. College of Architecture and Civil Engineering, Beijing University of Technology, Beijing 100124, China;
    2. Key Laboratory of Civil Engineering Safety and Durability of China Education Ministry, Department of Civil Engineering, Tsinghua University, Beijing 100084, China
  • Received:2017-09-28 Revised:2018-01-04 Online:2018-12-14 Published:2018-12-14

摘要: 为了研究不锈钢焊接箱形截面压弯构件的弯曲屈曲,该文对5根奥氏体型和5根双相型不锈钢焊接箱形截面柱进行了偏心受压试验,试件长细比在55~85,荷载偏心距分别设计为50 mm、60 mm、70 mm,并且在试验前对试件的初始弯曲和荷载初偏心进行了测量。根据试验结果对构件静力承载性能进行了分析,并将试验结果分别与CECS 410:2015《不锈钢结构技术规程》和欧洲规范EN 1993-1-4中不锈钢压弯构件承载力的计算值进行了对比。结果表明:所有构件均发生平面内的整体弯曲失稳,且整体失稳前没有发现明显的局部板件屈曲;构件承载力随着偏心距、长细比的增大而降低;对于双相型不锈钢压弯构件,依据CECS 410:2015和EN 1993-1-4的计算值较试验结果均偏于安全;对于奥氏体型不锈钢压弯构件,依据EN 1993-1-4的计算值较试验结果均偏于安全,依据CECS 410:2015的个别试件计算结果略低于试验结果,但整体偏于安全。

关键词: 不锈钢, 焊接箱形截面, 压弯构件, 试验研究, 整体稳定承载力

Abstract: In order to investigate flexural buckling of stainless steel welded box-section beam-columns, 5 austenitic and 5 duplex stainless steel welded box-section columns are loaded eccentrically, with values of slenderness varying from 55 to 85. The design loading eccentricities are 50 mm, 60 mm and 70 mm, and the initial bending and loading eccentricities are measured before the test. The static loading capacity of the components is analyzed based on the test results, which are compared with the predictions based on current specifications CECS 410:2015 and EN 1993-1-4. The results indicate that all members failed in the form of overall flexural buckling without obvious local buckling. The bearing capacity decreases with increase of slenderness and loading eccentricities. For the duplex stainless steel welded beam-columns, both EN 1993-1-4 and CECS 410:2015 provide conservative prediction on the loading capacity. Moreover, as for the austenitic stainless steel welded beam-columns, EN 1993-1-4 also provides conservative prediction on the loading capacity. Although the test results of individual specimens are slightly lower than the calculation results of CECS 410:2015, most prove to be safe generally.

Key words: stainless steel, welded box-section, beam-column, experimental research, overall buckling capacity

中图分类号: 

  • TU391
[1] 袁焕鑫. 焊接不锈钢轴心受压构件局部稳定和相关稳定性能研究[D]. 北京:清华大学, 2014. Yuan Huanxin. Local and local-overall buckling behaviour of welded stainless steel members under axial compression[D]. Beijing:Tsinghua University, 2014. (in Chinese)
[2] Tarcísio Reis de Oliveira, Roberto Bamenga Guida, 张岩. 不锈钢在巴西建筑中的应用[J]. 建筑技艺, 2011(6):164-167. Tarcísio Reis de Oliveira, Roberto Bamenga Guida, Zhang Yan. Stainless steel application in architecture and construction in brazil[J]. Architecture Technique, 2011(6):164-167. (in Chinese)
[3] 黄唯, 李宏, 李冰. 不锈钢板在广州亚运城综合体育馆围护系统中的运用[J]. 建筑技艺, 2011(11):170-173. Huang Wei, Li Hong, Li Bing. Application of stainless steel sheet in envelope system of gymnasium for Guangzhou asian games[J]. Architecture Technique, 2011(11):170-173. (in Chinese)
[4] 郑宝锋. 不锈钢冷弯薄壁型钢轴心受压和压弯构件理论分析与试验研究[D]. 南京:东南大学, 2010. Zheng Baofeng. Theoretical and experimental investigations on cold-formed stainless steel columns and beam-columns[D]. Nanjing:Southeast University, 2010. (in Chinese)
[5] 埃斯科·米耶蒂宁[芬兰]. 不锈钢与建筑[M]. 天津:天津大学出版社, 2004:9-10. Esko·Miettinen[Finland]. Stainless Steel in Architecture[M]. Tianjin:Tianjin University Press, 2004:9-10. (in Chinese)
[6] 杨璐, 徐东辰, 王元清, 等. 奥氏体型不锈钢焊接箱形截面轴压构件整体稳定性能试验研究[J]. 土木工程学报, 2014(8):83-88. Yang Lu, Xu Dongchen, Wang Yuanqing, et al. Experimental study on the overall buckling behavior of austenitic stainless steel columns under axial compression[J]. China Civil Engineering Journal, 2014(8):83-88. (in Chinese)
[7] 范圣刚, 孙文隽, 桂鹤阳, 等. 轴心受压H形截面不锈钢柱抗火性能分析[J]. 工程力学, 2016, 33(6):154-162. Fan Shenggang, Sun Wenjun, Gui Heyang, et al. Fire resisttance pereormance analysis of H-section stainless steel column under axial compression[J]. Engineering Mechanics, 2016, 33(6):154-162. (in Chinese)
[8] 袁焕鑫, 王元清, 石永久, 等. 焊接箱形截面不锈钢柱相关稳定性能分析[J]. 工程力学, 2015(9):84-91. Yuan Huanxin, Wang Yuanqing, Shi Yongjiu, et al. Behavior of interactive buckling in welded stainless steel box section columns[J]. Engineering Mechanics, 2015(9):84-91. (in Chinese)
[9] 杨璐, 徐东辰, 尚帆, 等. 双相型不锈钢焊接箱形截面轴压构件整体稳定性能试验研究[J]. 东南大学学报:自然科学版, 2015, 45(2):364-369. Yang Lu, Xu Dongchen, Shang Fan, et al. Experimental study on overall buckling behavior of duplex stainless steel welded box columns under axial compression[J]. Journal of Southeast University (Natural Science Edition), 2015, 45(2):364-369. (in Chinese)
[10] 杨璐, 尚帆, 赵梦晗, 等. 不锈钢工字形截面构件轴心受压整体稳定计算方法[J]. 湖南大学学报:自然科学版, 2016, 43(3):55-65. Yang Lu, Shang Fan, Zhao Menghan, et al. Calculation method of the overall stability for I-shaped stainless steel member under axial compression load[J]. Journal of Hunan University (Natural Science), 2016, 43(3):55-65. (in Chinese)
[11] 尚帆, 杨璐, 赵梦晗, 等. 不锈钢工字形截面轴心受压构件整体稳定性能有限元研究[J]. 工程力学, 2016(3):112-119. Shang Fan, Yang Lu, Zhao Menghan, et al. FEA of the overall stability for i-section stainless steel member under axial compression[J]. Engineering Mechanics, 2016(3):112-119. (in Chinese)
[12] Yang L, Zhao M H, Xu D C, et al. Flexural buckling behavior of welded stainless steel box-section columns[J]. Thin-Walled Structures, 2016, 104:185-197.
[13] Yang L, Zhao M, Chan T M, et al. Flexural buckling of welded austenitic and duplex stainless steel I-section columns[J]. Journal of Constructional Steel Research, 2016, 122:339-353.
[14] Yang L, Shi G, Zhao M H, et al. Research on interactive buckling behavior of welded steel box-section columns[J]. Thin-Walled Structures, 2017, 115:34-47.
[15] Anbarasu M, Ashraf M. Behaviour and design of cold-formed lean duplex stainless steel lipped channel columns[J]. Thin-Walled Structures, 2016, 104:106-115.
[16] Gardner L, Bu Y, Theofanous M. Laser-welded stainless steel I-sections:Residual stress measurements and column buckling tests[J]. Engineering Structures, 2016, 127:536-548.
[17] GB 50017-2017, 钢结构设计标准[S]. 北京:中国建筑工业出版, 2017. GB 50017-2017, Standard for design of steel structures[S]. Beijing:China Architecture & Building Presss, 2017. (in Chinese)
[18] CECS 410-2015, 不锈钢结构技术规程[S]. 北京:中国计划出版社, 2015. CECS410-2015, Technical specification for stainless steel structures[S]. Beijing:China Planning Press, 2015. (in Chinese)
[19] 员翔, 赵果, 段宝山, 等. 不锈钢方矩管压弯构件平面内稳定承载力理论研究[J]. 工业建筑, 2015, 43(3):150-155. Yuan Xiang, Zhao Guo, Duan Baoshan, et al. Theoretical research on in-plane stability capacity of rhs stainless Steel Beam-Columns[J]. Industrial Construction, 2015, 43(3):150-155. (in Chinese)
[20] Zheng B, Hua X, Shu G. Tests of cold-formed and welded stainless steel beam-columns[J]. Journal of Constructional Steel Research, 2015, 111:1-10.
[21] Lui W M, Ashraf M, Young B. Tests of cold-formed duplex stainless steel SHS beam-columns J]. Engineering Structures, 2014, 74:111-121.
[22] Huang Y, Young B. Experimental investigation of cold-formed lean duplex stainless steel beam-columns[J]. Thin-walled Structures, 2014, 76(3):105-117.
[23] Huang Y, Young B. Design of cold-formed lean duplex stainless steel members in combined compression and bending[J]. Journal of Structural Engineering, 2015, 141(5):1-10.
[24] 桥本政哲[日]. 不锈钢及其应用[M]. 北京:冶金工业出版社, 2011:226-238. Hashimoto[Japan]. Stainless steel and application[M]. Beijing:Metallurgical Industry Press, 2011:226-238. (in Chinese)
[25] GB/T 228.1-2010, 金属材料拉伸试验第1部分:室温试验方法[S]. 北京:中国标准出版社, 2010. GB/T228.1-2010, Metallic materials-Tensile testingPart1:Method of test at room temperature[S]. Beijing:Standards Press of China, 2010(in Chinese)
[26] 袁焕鑫, 王元清, 石永久, 等. 不锈钢焊接箱形截面柱轴心受压相关稳定试验研究[J]. 土木工程学报, 2015, 48(2):63-72. Yuan Huanxin, Wang Yuanqing, Shi Yongjiu, et al. Interactive buckling tests on welded stainless steel axial compression members with box sections[J]. China Civil Engineering Journal, 2015, 48(2):63-72. (in Chinese)
[27] 班慧勇, 施刚, 石永久, 等. Q460高强钢焊接箱形截面轴压构件整体稳定性能研究[J]. 建筑结构学报, 2013, 34(1):22-29. Ban Huiyong, Shi Gang, Shi Yongjiu, et al. Overall buckling behavior of Q460 high strength steel welded box section columns under axial compression[J]. Journal of Building Structures, 2013, 34(1):22-29. (in Chinese)
[28] EC3. Design of steel structures-Part 1-4:General rules-supplementary rules for stainless steels[S]. EN 1993-1-4, 2006.
[1] 丁杰, 邹昀, 蔡鑫, 李天祺, 郑黎君, 赵桃干. 损伤可控型钢框架边节点的试验研究[J]. 工程力学, 2018, 35(S1): 107-112.
[2] 刘晓, 徐建烨, 王兵. 高温后中空夹层钢管混凝土柱压弯机理分析[J]. 工程力学, 2018, 35(S1): 40-45.
[3] 齐欣, 许浒, 余志祥, 赵雷, 孟庆成. 柔性拦截结构中减压环动态力学性能试验研究[J]. 工程力学, 2018, 35(9): 188-196.
[4] 施刚, 王珣, 高阳, 张勇. 国产低屈服点钢材循环加载试验研究[J]. 工程力学, 2018, 35(8): 30-38.
[5] 孟宝, 钟炜辉, 郝际平. 基于节点刚度的钢框架梁柱子结构抗倒塌性能试验研究[J]. 工程力学, 2018, 35(6): 88-96.
[6] 李天, 晁进涛, 樊嘉. 等腰三角形空间桁架自由扭转理论分析和试验研究[J]. 工程力学, 2018, 35(5): 223-230,238.
[7] 刘希月, 王元清, 石永久, 谭清华. 高强度钢框架梁柱节点焊接构造的断裂性能试验研究[J]. 工程力学, 2018, 35(5): 54-64.
[8] 杨璐, 卫璇, 张有振, 常笑, 蒋庆林. 不锈钢母材及其焊缝金属材料单拉本构关系研究[J]. 工程力学, 2018, 35(5): 125-130,151.
[9] 管宇, 周绪红, 卫世杰, 石宇. 冷弯薄壁型钢组合楼盖振动性能及静力挠度研究[J]. 工程力学, 2018, 35(5): 131-142.
[10] 杨青顺, 甄伟, 陆新征, 解琳琳, 林楷奇. 带端部阻尼器伸臂桁架的抗震性能试验研究[J]. 工程力学, 2018, 35(2): 47-58.
[11] 杜新喜, 胡锐, 袁焕鑫, 程晓燕, 宗亮. 混合配筋预应力混凝土管桩抗剪性能试验研究[J]. 工程力学, 2018, 35(12): 71-80.
[12] 刘君平, 徐帅, 陈宝春. 钢-UHPC组合梁与钢-普通混凝土组合梁抗弯性能对比试验研究[J]. 工程力学, 2018, 35(11): 92-98,145.
[13] 杨勇, 陈展, 王念念, 张波. 预应力钢带加固RC框架节点抗震性能试验研究[J]. 工程力学, 2018, 35(11): 106-114,154.
[14] 庞瑞, 许清风, 梁书亭, 朱筱俊. 全装配式RC楼盖板缝节点拉剪复合受力性能试验研究[J]. 工程力学, 2018, 35(10): 112-123.
[15] 孟宝, 钟炜辉, 郝际平. 不同跨度比下栓焊刚性连接梁柱子结构抗倒塌性能试验研究[J]. 工程力学, 2018, 35(1): 79-87.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!
X

近日,本刊多次接到来电,称有不法网站冒充《工程力学》杂志官网,并向投稿人收取高额费用。在此,我们郑重申明:

1.《工程力学》官方网站是本刊唯一的投稿渠道(原网站已停用),《工程力学》所有刊载论文必须经本刊官方网站的在线投稿审稿系统完成评审。我们不接受邮件投稿,也不通过任何中介或编辑收费组稿。

2.《工程力学》在稿件符合投稿条件并接收后会发出接收通知,请作者在接到版面费或审稿费通知时,仔细检查收款人是否为“《工程力学》杂志社”,千万不要汇款给任何的个人账号。请广大读者、作者相互转告,广为宣传!如有疑问,请来电咨询:010-62788648。

感谢大家多年来对《工程力学》的支持与厚爱,欢迎继续关注我们!

《工程力学》杂志社

2018年11月15日